IP Power 9258

[mdsh]

Hi Kalle, hope I did this right.

Code Select Expand

<?xml version="1.0" encoding="utf-16"?>
<commandGroup open="True" name="test IP" enabled="True" prefix="" priority="0" requiredProcess="" description="">
 <command id="389" name="turn outlet on off" enabled="true" alwaysOn="False" confirm="False" requiredConfidence="0" loop="False" loopDelay="0" loopMax="0" description="">
   <if ifBlockDisabled="False" ifNot="False">
     <ifType>(A)==(B)</ifType>
     <ifParams>{2}&amp;&amp;on</ifParams>
     <then>
       <action>
         <cmdType>Scrape</cmdType>
         <cmdString>http://192.168.1.221/Set.cmd?CMD=SetPower+{1}=1&amp;&amp;admin&amp;&amp;12345678</cmdString>
         <cmdRepeat>1</cmdRepeat>
       </action>
     </then>
     <else>
       <action>
         <cmdType>Scrape</cmdType>
         <cmdString>http://192.168.1.221/Set.cmd?CMD=SetPower+{1}=1&amp;&amp;admin&amp;&amp;12345678</cmdString>
         <cmdRepeat>1</cmdRepeat>
       </action>
     </else>
   </if>
   <action>
     <cmdType>OSD.ShowText</cmdType>
     <cmdString>{LastResult}</cmdString>
     <cmdRepeat>1</cmdRepeat>
   </action>
   <phrase>turn socket</phrase>
   <payloadFromXML phraseOnly="False" use2partPhrase="False" phraseConnector="by" Phrase2wildcard="anyone" optional="False">IP power test.xml</payloadFromXML>
   <payloadList>on,off</payloadList>
 </command>
</commandGroup>

This is my code as per my last post with the attached picture.

Thank you guys very much for the help. I feel a bit silly but did try an make sure I coded right  
Also my xml phrase\value payload I just put in Value = P60 and Phrase = 1 as a test

[mdsh]

Hi James, I tried a purge as well as a rebuild grammer with no luck. Just looking at my code again tonight to see where I might have gone wrong

[mdsh]

  ITS SORTED GUYS!!!! Thanks again for all your help.

Suppose it was something I did wrong after all. So what I did was test my code (By the way Kalle I have both my arguments in my logic saying POWER ON at the end the =1 bit that I saw now as well and fixed) inside of the builder. So I was putting the value 1 in the payload one section and then either on or off in the payload two section of the builder. This returned the wrong values as mentioned before. But after doing a purge and then a grammer rebuild and a full restart of VC and it still not working I read that wiki link James posted more and that put me onto the TellVOX.exe. I typed my command out in this eg, turn socket {1} {2} - turn socket 1 on

This worked after all and then I went on to test it with voice and all seems fine!

Sorry for all the head scratching I might have caused you guys but thanks again for the help! I do appreciate it very much

[Kalle]

No problem  
I insert here a group (you need also the attached payload and put it in your VC mainfolder), that will show you a second way with only one payload and it show you also how you can use a action with payload friendly {PF.1} value.

Code Select Expand

<?xml version="1.0" encoding="utf-16"?>
<commandGroup open="False" name="test IP new" enabled="True" prefix="" priority="0" requiredProcess="" description="">
 <command id="408" name="turn outlet on off" enabled="true" alwaysOn="False" confirm="False" requiredConfidence="0" loop="False" loopDelay="0" loopMax="0" description="">
   <action>
     <cmdType>Scrape</cmdType>
     <cmdString>http://192.168.1.221/Set.cmd?CMD=SetPower+{1}&amp;&amp;admin&amp;&amp;12345678</cmdString>
     <cmdRepeat>1</cmdRepeat>
   </action>
   <action>
     <cmdType>OSD.ShowText</cmdType>
     <cmdString>{PF.1}</cmdString>
     <cmdRepeat>1</cmdRepeat>
   </action>
   <action>
     <cmdType>TTS.Speak</cmdType>
     <cmdString>I turn the {PF.1}</cmdString>
     <cmdRepeat>1</cmdRepeat>
   </action>
   <phrase>turn, switch</phrase>
   <payloadFromXML phraseOnly="False" use2partPhrase="False" phraseConnector="by" Phrase2wildcard="anyone" optional="False">IP power test new.xml</payloadFromXML>
 </command>
</commandGroup>

[mdsh]

Yeeessssss..... that is very clever Kalle!! Im sure I would have eventually gotten to that point! 

Thanks for sharing and again thanks to you guys for helping me troubleshoot!

[Kalle]

Also interesting for you is a map table, take a look in this video (especially after 5 min)

http://www.youtube.com/watch?v=k-kwIkmPDtI

[mdsh]

Thanks Kalle, I was this video from James and started using maps but still in the mindset of using two payloads. So when I actually got to the point of creating an action I ran into a few hurdles. But yes definitely the way you posted with the P60=1 or P60=0 all in one payload makes way more sense and would work really well with the maps I think as well.

Thanks for all the help Kalle!